1968-1969 Chevelle Notched Corner EFL Fuel Tank kit with 255LPH Pump

1968-1969 Chevelle Notched Corner EFL Fuel Tank kit with 255LPH Pump

1968-69 CHEVELLE, BEAUMONT/ 1970 BUICK SKYLARK, & GS EFI GAS TANK KIT; TANK, 255 LPH PUMP, SENDER, & STRAPS

TANKS, INC. has been a leader in the street rod industry, receiving various awards for safety and innovation. In addition, it was the first to introduce style into street rod gas tanks; radiused edges, die-stamped openings, flush-mounted fittings, indented panels and slotted mounting flanges, just to name a few.

This notched corner tank is perfect for mini-tub applications.  Both corners are notched 7″ in and 7″ back for better tire and exhaust clearance.  The rear of the tank is the stock depth while the front of the tank is 1″ deeper than stock.  This additional rake of the gas tank provides better fuel delivery to the pump.

1968-1969 Chevy Chevelle and Pontiac Beaumont EFI Tank

1970 Buick Skylark and GS EFI Tank

Fuel Injection Ready!

Includes 2 piece neck design that simply connects with supplied 2″ ID rubber hose.

Uses our GPA-6 series fuel pumps

Uses aftermarket 5-bolt sender 0 to 90 OHM range to work with factory or aftermarket gauges.

EFI style internal baffling with extra Large 4.8 liter dual tube baffled fuel tray to prevent fuel pump starvation.

ST49-Q 1968-1972 GM Gas Tank Straps

Fuel pump and sender are recessed in the tank for easy installation with no modification needed to your car.

Looks like an OE tank when installed.

Galvanized steel then Powder Coated Silver

20 Gallon Capacity

1″ Deeper than stock

Longer mounting straps included with the tank

39-1/4″ x 24-1/2″ x 8-3/4″

In-Tank Fuel Pump Module – GPA-6 Series

Made in the USA

Heavy 10 gauge no-warp mounting plate

1/4″ NPT Supply and Return Line

Barbed Vent Fitting

Oven brazed fittings

Up to 100 PSI

In-tank wire harness

Genuine Walbro Fuel Pump

The GPA-6 Series Fuel Pump Module is designed to be used in many of our die-stamped alloy-coated and stainless steel gas tanks that have factory-installed reservoir trays. The tray is an absolute necessity for fuel-injection in order to prevent fuel starvation when accelerating and cornering.

We use Walbro high-performance pumps in all of our fuel injection modules, and we offer four different operating ranges in order to supply up to approximately 1000 horsepower. The internal wiring harness, supply line, return line, filter sock and insulator sleeve are included. (The gasket and screws with o-rings are not included with the pump because we include gaskets and screws with our tanks.)

The heavy 10-gauge no-warp mounting plate contains fittings for the supply, the return, the vent and the electrical connector.  It is yellow-zinc plated to prevent corrosion.

5 Bolt Fuel Sending Unit

Our fuel tank senders mount with five mounting screws. They work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground they work on all 6-24 volt systems positive or negative ground. They do not have a fuel pickup tube built into them as some original senders may have.  Made with a high quality ceramic board rheostat. Our fuel senders are available for the following applications.

Application Listing:

GML – GM 1965 and up – 0-90 Ohms

EFI Gas Tank Kit includes:

20 gallon Tank

400 LPH Pump

0-90 ohms Sending Unit

Straps